Showing all 8 results

Edge Dual Carriage Mid Rail Waterjet

EDGE DUAL CARRIAGE

MID RAIL WATERJET

with Aquavision DI Controller

The Edge Dual Carriage waterjet cutting machine is for those who demand both accuracy and productivity from their investment. The dual Z carriages operate independently so they can be programmed to double team a single part or cut two like parts simultaneously. Boasting ±0.001″ linear positional accuracy over 12″ (304 mm) per axis, ±0.001″ repeatability (bidirectional) and ±0.003″ renishaw ballbar tests of squareness and straightness over 24″ (608 mm), means never giving up on precision again.

  • Specify 3-axis cutting heads, 5-axis cutting heads or one of each
  • Independently driven, dual Z carriages can cut a single part together or two like parts simultaneously
  • 5-axis cutting head can cut bevels to 60° and eliminate tapers
  • Programable Z carriage with servo motor driven 12″ (304 mm) vertical travel height
  • Multiple accessory options to further increase productivity
  • Isolated catch tank for the highest precision
  • Adjustable pre-loaded anti-backlash recirculating ball screws
  • Protected critical bearing components with labyrinth seals and positive air pressure
  • Technical service and free lifetime factory training

EDGE X3-HR

EDGE X3-HR

HIGH RAIL GANTRY 3-AXIS WATERJET

with with Aquavision DI Controller

The Edge X3-HR, 3-Axis High Rail Water Jet Cutter opens up the work envelope for easier access and the overhead design raises critical components out of the processing environment. The Edge X3-HR is designed for high speed processing.  By attaching a precision machined Spreader Bar to the Z Carriage, up to ten sub-Z cutting heads can be mounted allowing you to cut ten identical parts in one cycle. Each independently controlled Sub Z can utilize a water only cutting head or abrasive cutting head.  Heads can be positioned manually or positioned automatically via your program.  Incorporate load/unload systems for even higher efficiency levels as parts unloading is done while the water jet is cutting its next job. Click on the links to learn more about Custom Applications and Custom Configurations.

  • 3-axis waterjet or abrasivejet cutting
  • Independently programmable Sub Z’s
  • Isolated catch tank for accuracy
  • Adjustable pre-loaded anti-backlash recirculating ball screws
  • Linear bearings, hardened precision ground ways
  • Protected critical bearing components with labyrinth seals and positive air pressure
  • Direct-couple, AC brushless servo motors with absolute encoders
  • Technical service and free lifetime factory training

EDGE X5 HR

EDGE X5-HR

HIGH RAIL GANTRY 5 AXIS WATERJET

with with Aquavision DI Controller

There are many benefits to a High Rail Waterjet Machine. First of all, it opens the work envelope for easier access, and the overhead design raises critical components out of the processing environment. The isolated motion system and rigid steel beams make this the most accurate waterjet cutter on the market. Incorporating the 5-axis cutting head into your Edge X5-HR system allows you to bevel cut angles to 60° in the hardest materials with a taper-free finish.  Aerospace, contract manufacturing and highly specialized applications companies that require accuracy, repeatability and high machine uptime from their abrasive cutting have found their system.  Click on the links to learn more about Custom Applications and Custom Configurations.

  • Easy-access work envelope
  • Motion components protected from harsh process environment
  • 5-axis cutting head can cut bevels to 60° and eliminate tapers
  • Programable Z carriage with servo motor driven 12″ (304 mm) vertical travel height
  • Multiple Configuration Options including integrated fixtures and lights out cutting
  • Isolated catch tank for the highest precision
  • Adjustable pre-loaded anti-backlash recirculating ball screws
  • Linear bearings, hardened precision ground ways
  • Protected critical bearing components with labyrinth seals and positive air pressure
  • Direct-couple, AC brushless servo motors with absolute encoders
  • Technical service and free lifetime factory training

Jet Start 510A

JET START 510A

MID RAIL ABRASIVE WATERJET

with HERO 50 Intensifier Pump

The Jet Start 510A takes the no-nonsense workhorse 3-axis, 5′ x 10′ motion system and pairs it with Jet Edge’s HERO 50 intensifier pump that is loaded with features including Jet Smart controls. The result is an Abrasive Waterjet system capable of cutting complex parts from virtually any material with ultra-high precision. Jet Start your waterjet cutting operation with a Jet Start 510A Mid Rail Abrasive Waterjet system.

The Jet Start 510A waterjet cutting system includes a 3-axis abrasive cutting Z carriage, a rugged 5′ x 10′ isolated catcher tank, Jet Edge’s HERO 50 Intensifier Pump with Jet Smart Controls, IGEMS Software, an 800lb solid phase bulk hopper all with installation and training included.

  • Aquavision Di Controller for Windows 10
  • IGEMS Software with Nesting Program Upgrade
  • Motorized Z carriage for 12″ (304 mm) vertical travel height
  • Isolated Abrasive Catch Tank with Slat Kit
  • Full Featured Handheld Pendant
  • HERO 50 60k psi 50 hp intensifier pump
  • Remote Pump Start
  • 800lb Solid Phase Bulk Hopper
  • Installation and Training included

Jet Start 510A5

JET START 510A5

MID RAIL ABRASIVE WATERJET

with HERO 50 Intensifier Pump

The Jet Start 510A5, 5-axis motion system launches you into complex, contoured cutting right from the start. Cut near-net shapes with edges beveled up to 60° with no taper in tough materials like stainless steel, Inconel, and titanium with no heat affected zone.

The Jet Start 510A5 package includes a 5-axis abrasive cutting Z carriage, a rugged 5′ x 10′ isolated catcher tank, Jet Edge’s HERO 50 Intensifier Pump with Jet Smart Controls, IGEMS Software, an 800lb solid phase bulk hopper all with installation and training included.

  • Aquavision Di Controller for Windows 10
  • IGEMS Software with Nesting Program Upgrade
  • Servoed Z Package
  • Isolated Abrasive Catch Tank with Slat Kit
  • Full Featured Handheld Pendant
  • HERO 50 60k psi 50 hp intensifier pump
  • Remote Pump Start
  • 800lb Solid Phase Bulk Hopper
  • Installation and Training included

Edge X-3 Mid Rail Gantry Waterjet Cutting Machine

EDGE X-3

3-AXIS MID RAIL WATERJET

with Aquavision DI Controller

The Edge X-3 Mid Rail Gantry 3-axis water jet cutter is the no-nonsense workhorse of the Jet Edge line. Its 3-axis cutting capabilities excel at high-speed waterjet cutting and abrasivejet cutting and offers a slew of customization options. Paired with a Jet Edge HERO Series UHP Pump you have a committed cutting team!

  • Isolated catch tank for accuracy
  • Cut with water or abrasive
  • Multiple Configuration Options including independently programmable Dual Z Carriages
  • Adjustable pre-loaded anti-backlash recirculating ball screws
  • Linear bearings, hardened precision ground ways
  • Protected critical bearing components with labyrinth seals and positive air pressure
  • Direct-couple, AC brushless servo motors with absolute encoders
  • Technical service and free lifetime factory training

Edge X-HR High Rail Gantry Waterjet Cutter System

EDGE X-HR

HIGH RAIL GANTRY WATERJET

with Aquavision DI Controller

The High Rail Gantry opens the work envelope for easier access, and the overhead design raises critical components out of the processing environment. The isolated motion system and rigid steel beams make this the most accurate waterjet cutter on the market. With 3-axis and 5-axis cutting options, multi-table sizes, and a Jet Edge UHP Pump, you’re prepared to cut some serious volume.

  • Easy-access work envelope
  • Motion components protected from harsh process environment
  • Isolated motion system for accuracy
  • Linear bearings, hardened precision ground ways
  • Direct-couple, AC brushless servo motors with absolute encoders
  • Adjustable pre-loaded anti-backlash recirculating ball screws
  • Dual synchronized y-axis drive system
  • Technical service and free lifetime factory training

Edge X5 5-Axis Waterjet Cutting Machine

EDGE X-5

5-AXIS MID RAIL WATERJET

with Aquavision DI Controller

The Edge X-5 features 5-axis waterjet cutting that is capable of bevel cutting to 60°. Complex 3-D parts, including impellers, gears, and other precision parts can be cut in the hardest materials with a taper-free finish. Controlled with the fully networkable Aquavision DI, the system offers a host of options to custom configure it to your operation’s needs. Coupled with a Jet Edge HERO Pump, your system is ready for high volume 5-Axis Abrasive Waterjet cutting!

  • 5-axis cutting head can cut bevels to 60° and eliminate tapers
  • Programable Z carriage with servo motor driven 12″ (304 mm) vertical travel height
  • Multiple Configuration Options including independently programmable Dual Z Carriages
  • Isolated catch tank for the highest precision
  • Adjustable pre-loaded anti-backlash recirculating ball screws
  • Linear bearings, hardened precision ground ways
  • Protected critical bearing components with labyrinth seals and positive air pressure
  • Direct-couple, AC brushless servo motors with absolute encoders
  • Technical service and free lifetime factory training