ACCUMULATOR PRESSURE CHECK

MAINTENANCE TRAINING VIDEO

Watch to learn how to check & charge the Hydraulic Accumulator

Jet Edge uses hydraulic accumulators to reduce shock in the hydraulic system of its UHP Intensifier Pumps.  This results in a better performing system and lower maintenance costs.

By watching this video, you will learn:

  • How to measure the accumulator pressure
  • The tools required to perform the pressure check
  • How to recharge the accumulator

BLEED DOWN VALVE REPAIR

MAINTENANCE TRAINING VIDEO

Watch to learn how to repair the bleed down valve

The bleed down valve is a safety device used to relieve ultra-high pressure water from the Intensifier Pump in the event of a shutdown or an emergency stop.

By watching this video, you will learn:

  • What the components of the Bleed Down Valve are
  • Signs of Bleed Down Valve failure
  • Process to perform repair and parts required

GENERATION III INTENSIFIER SEAL CHANGE

MAINTENANCE TRAINING VIDEO

Watch to learn how to change a Generation III Intensifier Seal

Seals are used in the intensifier to allow the plunger to create pressure and to seal that pressure for use in the cutting system.  As high pressure seals wear, ultra-high water pressure begins to fall and leakage will occur.

By watching this video, you will learn:

  • Signs that Seals need to be changed and how to change them
  • Required tools and parts
  • Safety tips to isolate machine from utilities

OMNIJET III CUTTING HEAD REBUILD

MAINTENANCE TRAINING VIDEO

Watch to learn how to safely maintain your OmniJet III

Jet Edge offers water only and abrasive waterjet Cutting Heads. Over time, components wear and may begin to leak. Rebuilding your Cutting Head saves time and reduces maintenance cost when compared to a full replacement.

By watching this video, you will learn:

  • Diagnosing the source of leaks in the cutting head assembly
  • The components that make up the cutting head
  • Proper rebuild sequence and techniques
  • How to replace the Short Stop Filter to extend Orifice and Nozzle Life

PERMALIGN II CUTTING HEAD REBUILD

MAINTENANCE TRAINING VIDEO

Watch to learn how to change Abrasive Cutting Head components

Jet Edge offers water only and Abrasive Waterjet Cutting Heads. Over time, components wear and eventually fail or begin to leak impacting cut quality. Replacing wear components timely and safely ensures the speed and accuracy you demand from your Jet Edge System is consistently delivered.

By watching this video, you will learn:

  • Correct Nozzle, Orifice and Mixing Chamber replacement techniques
  • Inspection and cleaning importance for Cutting Head performance
  • Proper sealing and seating methods to avoid leaks

FLUSHING THE HP WATER SYSTEM

MAINTENANCE TRAINING VIDEO

Watch to learn how to flush the High-Pressure water system

Flushing the high-pressure water system removes debris that can accumulate in the HP Water System and damage an orifice as it exits the cutting head. Flushing the high-pressure water system is always necessary whenever work is performed on any of the high-pressure components prior to the orifice or after changing the low-pressure water filters.

By watching this video, you will learn:

  • Best practices to verify high-pressure water has been removed from the system
  • Procedures for safely isolating and flushing both water-only and Permalign II cutting heads
  • Best practices for removing & installing the Orifice to prevent Orifice damage
Intensifier Check Valve Service - Jet Edge

INTENSIFIER CHECK VALVE SERVICE

MAINTENANCE TRAINING VIDEO

Watch to learn how to Service the Intensifier Check Valve

Jet Edge intensifier pumps utilize high-pressure and low-pressure check valves to control the flow of process water in and out of the intensifier. Over time, the check valves wear and need to be serviced to prevent the intensifier from cycling erratically.

By watching this video, you will learn:

  • Intensifier Pump symptoms indicating a failed or worn check valve
  • How to inspect and replace the high-pressure check valve and low pressure poppet components
  • How to resurface the low-pressure sealing face of the check tube

WE KNOW HEAVY METAL

 

METFAB FOUND THE EDGE THEY NEEDED WITH THEIR JET EDGE
INTENSIFIER PUMP AND HIGH RAIL GANTRY

 

Seven years ago, Metfab invested in a Jet Edge High Rail Gentry Abrasive Waterjet Cutting System and Intensifier Pump. Download this case study to learn why Metfab continues to trust Jet Edge’s Waterjet Cutting systems and Intensifier pumps to power their business.

SCHEDULE A FREE APPLICATION ANALYSIS!

 

SEE HOW JET EDGE & JET EDGE WATERJET SYSTEMS ARE A CUT ABOVE THE REST.

 

Fill out the form below and one of our waterjet experts will reach out to schedule a FREE application analysis.

Linkedin